Skip to main content
Legia

IT Infrastructure & Cloud

Designing Office Wi-Fi: Access Point Count, Channels, and the Guest Network

Slow office Wi-Fi is rarely caused by the internet connection alone. This guide covers four design decisions: the number of access points, channels, network separation, and testing after installation.

SEO and Content Specialist

5 min read

A bundle of blue network cables on a switch rack

Short answer: office Wi-Fi design starts from the number of devices connected at the same time, not floor area alone. Calculate access points from capacity (one vendor guideline: about 25 devices per radio), use 5 GHz as the main band, use channels 1, 6, and 11 on 2.4 GHz so they do not interfere with each other, separate the guest network from the office network, and test the signal in every room after installation.

The complaint “the office Wi-Fi is slow” is often answered by upgrading the internet plan. The result is frequently disappointing, because the problem is in the local network: too few access points for the number of devices, channels that collide, or a single network shared by employees, guests, and operational equipment. The following four design decisions determine most of the outcome.

1. Calculate from capacity, not just coverage

One access point may cover a whole floor, but it cannot necessarily serve every device on that floor. Each access point radio shares its airtime with all connected devices. The more devices, the smaller each one’s share.

Cisco Meraki’s high-density design guide uses two calculations and takes the larger result:

  • From the device count: the number of 5 GHz devices connected at the same time, divided by about 25 devices per radio.
  • From traffic needs: the total application traffic required, divided by the traffic capacity of each access point.

Keep in mind that one employee can carry two or three devices: a laptop, a phone, and sometimes a tablet. Large meeting rooms and training areas need to be calculated separately because their density rises sharply at certain hours.

Illustration: office network

2. Choose bands and channels deliberately

Modern access points work on two main bands:

BandAdvantagesLimitations
2.4 GHzLonger range, better wall penetrationOnly three channels that do not overlap (1, 6, 11), more interference
5 GHzMore channels, higher throughputShorter range, more easily attenuated by walls

Some commonly used principles:

  • Make 5 GHz the main band for employee laptops and phones, and leave 2.4 GHz for older devices or devices that only support that band.
  • On 2.4 GHz, use only channels 1, 6, and 11, alternating between neighboring access points. Other channels overlap and only add interference.
  • In dense areas, a 20 MHz channel width is often better than 40 or 80 MHz, because more access points can get their own channel.
  • Adjust transmit power, do not always set it to maximum. A signal that is too strong makes devices stay on a distant access point when a closer one is available.

3. Place access points according to the floor plan

Access point positions are determined by the floor plan and building materials, not by where the power outlets are. Things to keep in mind:

  • On the ceiling, in the middle of the work area, not inside a cabinet or behind a metal rack.
  • Concrete walls, laminated glass, and elevators attenuate the signal far more than gypsum partitions.
  • Every access point is connected by LAN cable to a switch. Access points that connect to each other wirelessly (mesh) cut capacity and should only be used where cabling truly cannot be run. The considerations are covered in the article Is Wi-Fi Enough for an Office Without LAN Cables?.
  • A PoE switch makes installation easier, because a single cable carries both data and power to the access point.

4. Separate networks by user

One Wi-Fi name for everyone is the most common pattern and the riskiest. A common separation:

NetworkUsersRules
OfficeEmployee devicesAccess to servers and internal systems
GuestVisitorsInternet only, separate from the office network, password changed periodically
OperationalPrinters, CCTV, attendance machines, smart devicesOnly the access needed, cannot be reached from the guest network

This separation is done with VLANs on the switch and firewall rules, not just a different Wi-Fi name. Use WPA3 if all devices support it, or WPA2 with a strong password if older devices remain.

Test after installation

A design on paper needs to be proven on site. A sound test covers:

  1. Signal strength and quality in every room, including corners and meeting rooms. One vendor guideline recommends a signal-to-noise ratio of at least 25 dB across all served areas.
  2. Handoff between access points while walking during a video call.
  3. Load testing in the busiest room at peak hours.
  4. Guest network isolation: a device on the guest network must not be able to reach office printers or servers.

The results are recorded together with a floor plan of access point positions, so that later additions do not start from guesswork. The full list of items to check is in the Office Network Installation Checklist.

How Legia does it

In the Office Network Installation service, wireless device positions are determined during the site survey based on the building floor plan and the needs of each room. The installation covers wireless access points, switches, routers, and firewalls, along with separation of the guest, office, and operational networks. Every point is tested before handover, and you receive the cable route plan, point numbering, and configuration documentation.

Frequently asked questions

Is one expensive access point better than several ordinary ones?

Not always. Capacity is determined by the number of radios serving devices. Several correctly placed access points usually serve more devices than a single access point mounted in the middle.

Should the 2.4 GHz and 5 GHz Wi-Fi names be separated?

Usually not. Modern access points can steer devices to 5 GHz automatically under a single network name. Separate names are useful for older devices that only support 2.4 GHz.

Can an ordinary repeater be used to extend coverage?

A repeater splits the same capacity across two transmissions, so effective throughput drops. For an office, an additional access point connected by cable is the more stable choice.

Sources

Category IT Infrastructure & Cloud

Keep reading

Related articles

All Articles